APC SurgeArrest Professional PRO7 (Z98010201706)
APC SurgeArrest Professional PRO7 (Z98010201706)
Overview
The APC SurgeArrest Professional PRO7 is a seven-outlet surge protector manufactured by APC.
The documented example bears serial number Z98010201706 and is believed to have been manufactured during 1998 based upon APC recall documentation and serial-number information.
This specimen represents the earliest APC PRO7 currently documented by the OldSurge Archive and predates the archive's other documented PRO7 examples by approximately a decade.
Inspection identified a surge-suppression circuit board marked ©1996, providing evidence that the underlying design predates manufacture of the documented example.
This specimen falls within the production period associated with the 2013 APC SurgeArrest recall.
Documented Example
- OldSurge ID: OS-0015
- Model: PRO7
- Serial Number: Z98010201706
- Manufacturing Date: 1998
Specifications
- Manufacturer: APC
- Product Family: SurgeArrest Professional
- Model: PRO7
- Device Type: Surge Protector
- Outlets: 7 grounded outlets
- Country of Origin: China
- Length:
- Approximately 10.25 in (26.0 cm) along the long edge
- Approximately 9.0 in (22.9 cm) along the curved edge
- Width:
- Approximately 4.19 in (10.6 cm) at the base
- Height:
- Approximately 1.25 in (3.2 cm) at the outlet section
- Approximately 1.75 in (4.4 cm) at the control section
- Power Cord Length: Approximately 6 ft (1.8 m)
- Power Cord Type: SJT
- Conductors: 16/3
- Cord Manufacturer: Hon-Eagle
- UL File Number (Cord): E133710
- CSA File Number: LL55737
- UL File Number: E111219
- UL 1363 Power Tap
- UL 1449 TVSS
- TVSS Ratings:
- Line-to-Neutral (L-N): 330 V
- Line-to-Ground (L-G): 330 V
- Neutral-to-Ground (N-G): 330 V
Weight
The documented example weighs approximately 1 lb 15.9 oz (903 g).
This is substantially heavier than the 2008 APC PRO7 specimen documented elsewhere in the archive, suggesting differences in internal construction, suppression components, bus bars, or power-cord assembly between production generations.
Physical Description
The APC SurgeArrest Professional PRO7 utilizes a rounded upper housing and a flat outlet section containing seven grounded outlets.
The control section incorporates a green Protection Working indicator, red Site Wiring Fault indicator, and a combined rocker-switch and circuit-breaker assembly.
Compared with later documented PRO7 examples, the overall enclosure architecture appears unchanged, demonstrating APC's long-term use of a successful mechanical design.
Unlike the 2008 PRO7 example documented by the archive, this earlier specimen exhibits comparatively little enclosure yellowing despite being substantially older. The difference suggests that environmental exposure and storage conditions may play a greater role in enclosure discoloration than chronological age alone.
The underside incorporates two keyhole-style mounting slots for wall or surface mounting.
The PRO7 utilizes a right-angle grounded plug intended to reduce the space required behind furniture and equipment.
When connected to modern receptacles installed with the grounding pin in the upward orientation, the cord exits upward before bending downward, making the arrangement somewhat less convenient than many modern low-profile plug designs.
The PRO7 utilizes a right-angle grounded attachment plug intended to reduce the distance between the connected device and the wall.
When installed in modern receptacles configured with the grounding contact in the upward position, however, the design causes the power cord to exit upward before bending downward. As a result, the plug does not sit as close to the wall as more modern low-profile right-angle plug designs.
Product Gallery
-
Overall view of the documented APC PRO7 example. -
APC branding and Protection Working indicator. -
Protection Working indicator, Site Wiring Fault indicator, and rocker-switch assembly. -
Flat-side profile view of the APC SurgeArrest Professional PRO7. -
Cord-entry end showing the rocker switch, resettable circuit breaker, and power-cord strain relief. -
Rounded outlet-end profile of the APC SurgeArrest Professional PRO7. -
Underside view showing labels, mounting slots, cord routing, and attached power cord. -
Product information label, serial-number label, and mounting provisions on the underside of the PRO7. -
Model and serial-number label identifying the documented PRO7 specimen. -
Right-side underside detail showing mounting provisions, serial-number label, and UL listing label. -
UL listing label identifying the device as a listed Power Tap and TVSS. -
Right-angle attachment plug and attached six-foot power cord. -
Close-up of the right-angle grounded attachment plug. -
Power-cord markings showing SJT construction, UL and CSA approvals, and manufacturer information. -
Additional power-cord markings showing conductor size, certification markings, and manufacturer information.
Testing
The documented example was tested for basic electrical operation.
The rocker switch successfully controlled power to all outlets.
When connected to a properly wired receptacle and switched ON, the green Protection Working indicator illuminated normally, indicating the continued presence of functional surge-protection circuitry.
The red Site Wiring Fault indicator remained unlit during testing.
When switched OFF, both indicators extinguished and power was removed from the outlet bank.
The documented example appears operational and functional following basic electrical testing.
Testing with a receptacle tester confirmed correct hot, neutral, and ground wiring.
No open ground, open neutral, reversed polarity, or other wiring faults were detected.
The documented example passed basic outlet-wiring verification.
-
Protection Working indicator illuminated with the PRO7 connected to power and switched ON. -
PRO7 connected to power with the rocker switch in the OFF position and indicator lights extinguished. -
Outlet tester indicating correct wiring and grounding. -
Right-angle plug installed in a wall receptacle illustrating cord routing.
Condition Upon Acquisition
The documented example was acquired as part of a lot containing twelve APC SurgeArrest Professional surge protectors.
The enclosure exhibited light dust accumulation, cosmetic wear, and moderate cord discoloration consistent with long-term use and storage.
Unlike some later PRO7 examples documented by the archive, the enclosure exhibited relatively little yellowing despite its apparent age.
The unit was cleaned prior to detailed documentation and photography.
Recall Information
Based upon its serial number, this specimen falls within the production period covered by the 2013 APC SurgeArrest recall.
As of September 2026, the documented example remains in the possession of the OldSurge Archive pending additional research regarding recall eligibility and available remedies.
For additional information, see:
Teardown
Inspection revealed a surge-suppression circuit board marked ©1996.
The APC SurgeArrest Professional PRO7 is assembled using seven screws and can normally be opened non-destructively.
During disassembly, six of the seven enclosure screws were successfully removed. The remaining screw was found attached to a fractured internal mounting boss that remained secured to the grounding bus bar.
The damage was not externally visible prior to opening the enclosure. The cause could not be determined and may have resulted from shipping damage, previous disassembly, long-term mechanical stress, or age-related plastic embrittlement.
Because the fractured boss remained attached to the grounding bus bar, the grounding assembly remained partially secured to the upper housing when the enclosure halves were separated.
The upper housing incorporates molded outlet barriers, structural reinforcing ribs, grounding-bus-bar supports, and provisions for mounting the outlet-contact assemblies.
-
PRO7 opened following removal of the enclosure screws. -
Six of the seven enclosure screws removed during disassembly. -
Interior details of the upper housing showing outlet barriers and grounding bus bar supports. -
Fractured mounting boss and grounding bus bar attachment point. -
Upper housing interior showing outlet supports, grounding bus bar, and structural details.
Comparison Notes
The APC PRO7 examples currently documented by the OldSurge Archive span approximately two decades of production.
The documented examples presently include:
- Z98010201706 (1998, ©1996 PCB)
- 4Z0842P07546 (2008, ©2002 PCB)
- 7Z1714L05335 (2017, ©2009 PCB)
Together these examples illustrate the long production life of the APC SurgeArrest Professional PRO7 and provide evidence of multiple suppression-board revisions while retaining substantially similar external appearance and mechanical architecture.